Equisol E365 – Timber Stabilising Pro Oil

• Easy single pack application
• Easy to use and maintain
• 2 coat system
• Penetrating timber oil stabilises timber moisture content and allows water to escape instead of sealing it in under film
• Water repellent to keep timber dry from the inside out.
• Non film-forming
• Dirt Resistant
• Scratch resistant and easily repaired
• No cracking, peeling or blistering
• Enhanced UV absorbers
• Formulated for harsh Australian sub-tropical climate
• Matt finish enhances natural timber grain and beauty
• Protects against effects of moisture, sunlight and mould
• Nourishes timber to minimise cupping, warping and splitting
• Includes powerful mouldicide and algicide
• Effective in sealing pressure treated timbers
• Can be applied on fresh timber without weathering
• Can be applied to seasoned or unseasoned timber
• Recommended for pre-finishing/pre-oiling before installation
• Can be wet stacked for easy pre-oiling
• No oily residues weeks after coating in cold wet climates
• May be applied to either rough sawn or dressed timber
• 2 coats are all that needed
• Range of 6 architectural colour tones can be mixed in, or leave as clear to allow timber to silver naturally
• No sanding in-between coats
• Can be recoated once touch dry (for best result, leave for 24 hours if possible)
• Can be applied in direct sun and cold weather
• Clear coat is clear without green staining
• No wet edge
• Easy maintenance – can be recoated without harsh sanding

Suitable for:

• Hardwoods and softwoods
• Sealing pressure treated timber
• Previously coated timber
• Weathered timber
• New and bare timber without weathering
• Seasoned or unseasoned timber
• Timber decks
• Decking substructure
• Retaining walls
• Cladding and weatherboard
• Exposed beams
• Railings
• Windows
• Doors
• Shutters
• Shingles
• Slat screens
• Outdoor furniture
• Timber soffits
• Fascia boards
• Garage doors
• Fences
• Posts
• Interior beams
• Interior panelling
• Teak decks on boats
• Glulam timbers
• Laminated timber, where individual sheets are 3mm thickness or more
  

Not suitable for:

• Interior floors
• Laminated timber, where individual sheets are below 3mm thickness
• Plywood
• All types of eco-timbers
• Timber substitutes
• Application in temperatures under 10°C or above 35°C
• When rain or heavy dew is expected within the coating dry time

Reapply when the timber has faded to a pale colour or water is not beading on the surface.

FIRST RECOAT: The process of removing previously failed finishes dries out the natural oils in the timber, so an initial recoat may be required sooner as timber absorbs the Equisol oil and Colour Tone. It is recommended to apply the first recoat in approximately six months if the timber is fully exposed to the weather. Once your timber has achieved a natural balance of oils again, the freshly oiled look will last longer.

REGULAR RECOATS: Multiple coats of Equisol with Colour Tone will darken timber over time, so prepare surface first with Equisol Vitalise to remove old colour, dirt, surface contaminants, grease, rust and water stains. Sand areas of broken or uneven colour with 80 grit sandpaper.

PROCESS: Apply one light coat of Equisol Pro E365 to the clean, dry surface. Frequency of recoating will vary depending upon degree of exposure, intensity of pigment, climate, aspect, etc. Initial signs of wear will be observed on exposed areas. Horizontal surfaces (eg. decks and handrails) require shorter interval before recoating than vertical parts, as water and dirt lying on the surface and long sun exposure will erode treatment more rapidly.

More than two coats per recoating are not recommended, as Equisol Pro E365 will not penetrate timber, resulting in stickiness, uneven surface colour and sheen.

THINNING: Does not require thinning.

DRYING TIME: Drying times are dependent on timber type, moisture and climate.

RECOAT: Leave for 24 hours if possible

WALK ON: 24 hours after recoat, or when dry.

Stir thoroughly before and during application with a flat blade stirrer. Apply two coats using a brush, spray or floor applicator.

On the first coat, ensure timber surface is touch dry, free of mould, wax, grease, dirt, and salt (coastal areas). Apply light coats. Drag each brush stoke out.

When using Equisol Colour Tones, follow directions on Colour Tones label. If job requires more than one tin of coloured Equisol, mix all together in large container prior to commencing for consistent colours.

Application can be used by spraying, lambswool applicator pad or brush. If applying with spray, back brush coating to ensure even penetration. Work along 3 – 4 planks at a time, in the direction of the grain. Ensure edges and end grain are fully coated.

Allow touch dry between coats. Do not apply under 10°C or above 35°C or when rain or heavy dew is expected within the drying time.

On previously coated timber using Equisol Pro E365 or equivalent penetrating oil.

Previous water-based coatings must be totally removed from surface or Equisol will remain sticky and shiny spots will develop. See PREPARATION.

Reapply when the timber has faded to a pale colour or water is not beading on the surface.

FIRST RE-COAT: The process of removing previously failed finishes dries out the natural oils in the timber, so an initial re-coat may be required sooner as timber absorbs the Equisol oil and Colour Tone. It is recommended to apply the first re-coat in approximately six months if the timber is fully exposed to the weather. Once your timber has achieved a natural balance of oils again, the freshly oiled look will last longer.

REGULAR RE-COATS: Multiple coats of Equisol with Colour Tone will darken timber over time, so prepare surface first with Equisol Vitalise to remove old colour, dirt, surface contaminants, grease, rust and water stains. Sand areas of broken or uneven colour with 80 grit sandpaper.

PROCESS: Apply one light coat of Equisol Pro E365 to the clean, dry surface. Frequency of re-coating will vary depending upon degree of exposure, intensity of pigment, climate, aspect, etc. Initial signs of wear will be observed on exposed areas. Horizontal surfaces (eg. decks and handrails) require shorter interval before re-coating than vertical parts, as water and dirt lying on the surface and long sun exposure will erode treatment more rapidly.

More than two coats per re-coating are not recommended, as Equisol Pro E365 will not penetrate timber, resulting in stickiness, uneven surface colour and sheen.

May be harmful if swallowed and enters airways.

May cause allergic skin reaction. May cause drowsiness or dizziness. Keep out of reach of children. Read the label before opening or using. Keep away from all sources of ignition – NO smoking. Keep container tightly closed. Ground/bond container and receiving equipment. Use explosion-proof electrical, ventilating, lighting and all other equipment. Use only non-sparking tools. Take precautionary measures against static discharge.

Avoid breathing mist, vapours or spray. Use only outdoors or in well-ventilated are. Wear protective 
clothing, gloves, eye/face protection and suitable respirator as required. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before re-use. Wash hands, face and all exposed skin thoroughly after handling. Store locked up. Store in a well ventilated place and away from oxidizing agents and foodstuffs. Keep cool. Do not empty into drains.

FIRST AID: If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 
13 11 26). If medical advice is needed, have product container or label at hand.

SWALLOWED: If swallowed, rinse mouth. Do NOT induce vomiting. Give a glass of water. Immediately call a POISON CENTRE or doctor/physician.

EYE: If in eyes, hold eyes open, flush with running water for at least 15 minutes and see a doctor.

SKIN: If skin or hair contact occurs, immediately remove any contaminated clothing and wash skin and hair thoroughly with running water. If swelling, redness, blistering or irritation occurs seek medical assistance.

INHALED: Remove from contaminated area – avoid becoming a casualty. Allow patient to assume most comfortable position and keep warm. Apply artificial respiration if not breathing. Seek medical advice.

FOR FIRE: If involved in fire use alcohol resistant foam. If unavailable, use standard foam or dry agents. Avoid breathing product of combustion.

FOR SPILLS: Clear area of all unprotected personnel. Slippery when spilt. Wear protective equipment. Absorb with sand or soil. Collect and seal in properly labeled drums. Dispose of contents/containers in accordance with local, regional, national and international.

DISPOSAL: Do NOT pour leftover product down the drain. Keep unwanted product in sealed containers for disposal via special chemical waste collections. Dispose of contents/containers in accordance with local, regional, national and international regulations.

DO NOT REUSE CONTAINER. SEE THE SAFETY DATA SHEET FOR ADDITIONAL INFORMATION.